SbD Fire & Security, Logo

Phone Icon Call: 01628 246707


Fire Detection is Our Business

In the event of a fire it is imperative that smoke is detected at the earliest stage to minimise the
resultant damage to property and potential risk to life. In kitchens or other areas where smoke detectors are impractical it is normal practice to install heat detectors. SbD Fire & Security can provide the most suitable and efficient system for Fire Protection covering all types of application.


Sigma CP

Types of Fire Detection

SbD Fire & Security offer Fire protection systems using four main types of detection equipment which are generally defined by the environment into which they are to be installed.

 


Optical Smoke Detectors

Optical Smoke Detectors

Optical Smoke Detectors incorporate a sensing chamber housing an infrared light emitting LED and photo diode located within the housing. When smoke enters the detection chamber a fraction of the collimated light is scattered onto the photo diode. If the resulting signal from the photo diode is above a preset threshold the detector will enter into a state of alarm.

Series 65 Heat Detector

Heat Detectors

Heat Detectors operate using a pair of matched negative temperature co-efficient thermistors mounted in such a way that one thermistor is exposed to give good thermal contact with the surrounding air while the other is thermally insulated. Under stable conditions both thermistors are in thermal equilibrium and have the same value of resistance. If air temperature increases rapidly the resistance of the exposed thermistor becomes less than that of the insulated thermistor. If the ratio of resistance between the two thermistors exceeds a preset level a state of alarm is initiated.

Beam Smoke Detectors

Beam Smoke Detectors

Beam Smoke Detectors (Reflective) are normally specified for large open areas such as atria, warehouses, theatres, churches etc. The transmitter and receiver form a single unit mounted to a wall. The unit emits an infrared beam to a reflector mounted on the opposite wall and in the event of smoke partially obscuring the beam an inbalance will occur initiating a state of alarm.

Vesda - Aspirating Smoke Detection

Aspirating Smoke Detection

Aspirating Smoke Detection provides very early warning of a potential fire hazard with continuous air sampling through an appropriately designed series of pipes. Air drawn through the pipes is monitored by a smoke detection unit with multiple levels of sensitivity to suit a variety of applications. With the detection unit set for high sensitivity extremely small levels of smoke can be detected thus providing the ultimate fire protection system.


Types of Fire Alarm Systems

Conventional Fire Alarm System

Sigma CP
In a Conventional system trigger devices (Detectors & Call Points) are hard wired into zoned circuits. Each zone circuit covers a different area of the premises in a design to comply with BS5839 Pt.1-2013.Alarm Sounders are normally wired using one of the following methods: 4-Wire method  -  Sounders wired on a minimum of two separate sounder circuits. 2-Wire method  -  Sounders wired on the same circuits as the trigger devices  (Special 2-Wire Control Panel required).The trigger devices signal fire or fault conditions to the Control Panel by changing from high to low impedence.  The panel detects this impedence change by current monitoring and identifies the zone from which the signal was sent. A conventional system cannot identify individual device from which the signal was sent.

Analogue Addressable Fire Alarm SystemSyncro-1
Addressable (Intelligent) systems incorporate hard wired loops and each trigger device has a unique address code. The Control Panel carries out a polling routine in which each device is interrogated in a programmed sequence. Devices respond with a status report which, as confirmation that the correct device is responding, includes its own address code. Alarm sounders are wired either on separate circuits or incorporated into the detection loops. Intelligent systems give advance warning of a developing hazard and pinpoint the individual device raising the alarm. It is possible to follow the spread or progress of a fire as individual detectors report conditions in their area.  This could allow a phased evacuation and provide important information for fire fighting teams

Radio Fire Alarm System

Hyfire System

Radio (Wire-Free) systems offer solutions where hard wiring of devices is impractical or undesirable. Each device is monitord in a programmed sequence and alarm and fault signals are sent via the radio network infrastructure to the control panel. From the incoming radio signal the control panel identifies the device from which the signal was sent. The system can be interrogated to provide information on historical events which can be useful when investigating previous faults or false alarms.  Installation of a radio system takes a fraction of the time for that of a hard wired system and because there is no wiring causes minimal disruption to décor.